Laptop mounting Arm & Platform Assembly.

Super strong extremely adjustable mounting arm and tray for Laptop computers or LCD monitors with permanently attached bases or without the VESA hole pattern on the back.

Can be mounted using either #8 or #10 wood or machine screws (not supplied). Single arm design with a ball and socket type adjustment. Easily repositions with just a twist of the easy to grab knob.

Super strong design, these components are actually qualified for mounting equipment in military vehicles. Yet with the cast aluminum arm construction it weighs less than 3 pounds. Will easily handle loads up to 10 lbs.

Maximum base to shelf height is approximately 8.5 inches. Platform is constructed from high impact plastic and is approximately 10inches deep and holds Laptops from 10 to 15 inches wide. Adjustable grippers, and a spring loaded clamping system built into the platform keep the laptop in place at any angle.

Can also be used as an secondary mounting shelf for the Monitor Jack based EasyChair Workstations.

Double Ball & Socket joints allow for an extremely wide adjustment for angle. The base may also be attached to vertical surfaces for use as a wall mounted platform for your laptop or other device.
Another application is for a vehicle mount for your laptop. Just securely mount the base to you center console, and your laptop will be at your fingertips. We also have a vehicle support base which clamp onto the support rails of the passenger seat of an auto, truck, or airplane. Please call for more information.

Please call if you have a special application as we can also mix and match these components for hundreds of variations.

List price $150.00

RM-01 Laptop Platform & Arm (single link, Flat mount) Price: $166.25

RM-11 Width extension for Laptop Platform assembly

RM-12 Screen Support For Laptop Platform

RM-12 Screen Support For Laptop Platform Price: $15.00

Ball Base only (Flat Surface Mount)

Additional Mounting Base for Laptop Mounting arm, or LCD mounting arm. Allows easy movement of Laptop Mounting platform & arm between vehicles or locations. The Mounting base is permanently affixed to its location, but with just a twist of the knob on the side of the arm link, the arm & platform can be removed or installed on the mounting base. Put a mounting base in each of your cars, or put one on your desk or even attach one to you easychair, and move the laptop platform & arm where you need it. (#8 or #10 screws needed to attach to surface - not supplied.) Base is 2 inches in diameter, and ball is 1.5inches in diameter.

Ball Base only U-Bolt Clamp Mount for 3/4 to 1-1/8 dia tubing.

Additional Mounting Base for Laptop Mounting arm, or LCD mounting arm. Allows easy movement of Laptop Mounting platform & arm between vehicles or locations. The Mounting base is permanently affixed to its location, but with just a twist of the knob on the side of the arm link, the arm & platform can be removed or installed on the mounting base. Put a mounting base in each of your cars, or put one on your desk or even attach one to you easychair, and move the laptop platform & arm where you need it. Will mount to pipe or tubing between 3/4 and 1-1/8 inches in diameter.

Socket Arm Only

Use with the ball base ends (either RM-02 or RM-02c) to make an adjustable support arm set. Note this item cannot be used alone -- it will need a ball base (either clamp or flat) for each end to make a complete support arm set. The Socket Arm with two ball base ends is about 8 inches in total length. The following RM-03 set may be used if you need to add length to make a dual link support arm.

Ball & Socket Arm Link only

A double ended ball unit, and Socket Arm set. Adds an additional link set to the arm on either the Laptop Platform & arm, or the LCD mounting arm. Adds about 7 inches to the total length of the arm, and another Ball and socket joint set which increases angle adjustment options. Caution: more that two links total, and the extra length can cause the platform to be less rigid.

Universal Drink Cup Holder.

You ask for it, here it is. A convenient place to put your drink while you are using your computer.

Universal design, will hold coffee cups, Beverage cans, glasses, and most fast food type drink cups. Built in auto leveling, can also be used in vehicles.

Two ball and socket joints let you position the cup-holder where you need it with just a twist of a knob.

Aluminum arm and base construction with high impact cup swing. Comes with an insulated cozy for cans. U-Bolt base may mount to 1in dia tube, or mounts to a horizontal or vertical flat surface.

Std List price $60

RM-06s Universal Drink Cup Holder (U-Bolt mount) Price: $57.00

HEAVY DUTY - VESA LCD Monitor Arm for Starbase Workstation (single link).

A much "beefier" version of our VESA monitor mount for the Boom Arm Starbase Workstation. This VESA mount Will support the larger 19 to 22 inch LCD flatscreen monitors up to 22 pounds. This will also work with the Apple iMac G5 with its VESA Mount. Note: additional counterbalance base weight plates may be needed on workstations with heavier monitors or other options mounted on the boom arm.

Ergonomic Accesories:

Clamp-on Mouse Platform.

Sturdy clamp attaches firmly to any desk up to 1.57" (4cm) thick.

Lowers mouse platform down to armrest level of chair, reduces arm movement.

Platform rotates 360 degrees, tucks under desk top when not in use.

Built in mouse cable clip keeps mouse in place. Neoprene mouse pad for accurate tracking.

List price $49.49

30 inch Boom Arm Stainless Steel Tube Only.

30 inch Boom Arm Stainless Steel Tube Only, with no clamps or attachments. This tubing only may be ordered for existing, already shipped workstations to replace an existing Stainless Steel Boom Arm with a longer 30 inch boom arm. Allows for extra space when mounting two or more devices on the boom arm. Note that this does NOT include the boom arm clamp. Use the STA-00 option if you wish to add a second boom arm to your workstation.